Search found 90 matches

by RCTID
Wed Apr 22, 2015 3:36 pm
Forum: Yamaha Enduro General Discussions
Topic: The Losers...
Replies: 3
Views: 134

The Losers...

https://www.youtube.com/watch?v=gtD2rz7pcSU

I'll be adding machine-guns to my to-do list.
by RCTID
Tue Apr 14, 2015 8:53 pm
Forum: Maintenance & Repair
Topic: rt2 - wont shift
Replies: 9
Views: 182

Thanks Apex. I have a new flat washer and thrust plate on the way. This time I'll double check to make sure nothing shifts around before I tighten anything.... Is that what you call experience? Yes, the gear in my clutch basket does go on the outside/behind... not inside the clutch basket. Thanks ag...
by RCTID
Mon Apr 13, 2015 10:21 pm
Forum: Maintenance & Repair
Topic: rt2 - wont shift
Replies: 9
Views: 182

One of my problems had to do with #30 not being in the correct position. http://www.yamahasportsplaza.com/oemparts/a/yam/50041689f8700209bc784802/shifter-a It's backwards here, right? I need to flip it around so the lip goes behind the lever shift? http://i76.photobucket.com/albums/j21/danquintero/D...
by RCTID
Sun Apr 12, 2015 10:01 pm
Forum: Maintenance & Repair
Topic: rt2 - wont shift
Replies: 9
Views: 182

Thanks. I took a look at some exploded diagrams, looked through my manual, checked out this How To ( http://www.yamahaenduro.com/showthread.php?t=23089 ) and I'm still stuck. I popped off the clutch basket thinking the bearing might have gone rogue, again, but everything seemed to be there. What I d...
by RCTID
Sun Apr 12, 2015 7:32 pm
Forum: Maintenance & Repair
Topic: rt2 - wont shift
Replies: 9
Views: 182

rt2 - wont shift

I recently replaced the crank seals on my rt2. I put everything back together (the way I thought it came apart) and now it wont come out of neutral. I'm thinking it might have something to do with the way I put the clutch basket back in...? Is there a certain way that's supposed to go on? Anything e...
by RCTID
Tue Mar 31, 2015 10:59 am
Forum: Maintenance & Repair
Topic: at2 - how to remove Starter Gen Assembly
Replies: 13
Views: 253

Here's what I ended up doing. Got two 10-1.25x50mm bolts (the longest fully threaded I could find locally). Cut off the head of one bolt, cut it down to 1.5", and ground off the thread. Slid the cut one into the armature first and then used the bolt with threads to turn the armature out. Looking bac...
by RCTID
Sun Mar 29, 2015 11:18 pm
Forum: Maintenance & Repair
Topic: at2 - how to remove Starter Gen Assembly
Replies: 13
Views: 253

Awesome. Thanks.
by RCTID
Sun Mar 29, 2015 7:17 pm
Forum: Maintenance & Repair
Topic: at2 - how to remove Starter Gen Assembly
Replies: 13
Views: 253

I've been all over town looking for this bolt. I checked out that link to the bolts and they're only 50mm which is just under 2". Can someone point me to where I can find that bolt - 10-1.25x3"?

Or if someone could elaborate on Fine69's idea of using a 10mm spacer?
by RCTID
Sat Mar 28, 2015 11:45 pm
Forum: Maintenance & Repair
Topic: at2 - how to remove Starter Gen Assembly
Replies: 13
Views: 253

I couldn't find a 1.25 piece of all thread rod. I believe that is what Capt Dave uses. If you can come up with a suitable spacer around 10mm you could slip it in and a good amount of threads should engage the amateur and pop it off. Its lightly pressed on the shaft. Re installation will pull it bac...
by RCTID
Sat Mar 28, 2015 8:58 pm
Forum: Maintenance & Repair
Topic: at2 - how to remove Starter Gen Assembly
Replies: 13
Views: 253

Thanks guys. I'm going to try tracking down that bolt before forking over for the sliding hammer.